AZ-801 무료 덤프문제 온라인 액세스

You plan to deploy an Azure confidential virtual machine named VM1. You need to ensure that you can implement confidential disk encryption for VM1. What should you do? To answer, select the appropriate options in the answer area. NOTE: Each correct selection is worth one point.

정답:

Explanation:
CORRECTED ANSWER: Use virtual machine series: DC. Disks that can be encrypted: The operating system disk only.
Detailed Explanation
Confidential disk encryption is a platform feature available only on confidential VM sizes such as the DCasv5
/DCadsv5/DCesv6 (and equivalent ECasv5/ECesv6) series, so VM1 must be deployed on a DC-series confidential SKU rather than the NC (GPU) or HB (HPC) families. Confidential disk encryption itself binds the encryption key to the VM ' s own vTPM and, by design, protects the operating system disk; the temp disk can optionally be added through a separate confidential temp disk encryption extension, but data disks are not covered by this mechanism and instead rely on guest-level encryption such as BitLocker if extra protection is required. Consequently the disk scope for confidential disk encryption is the operating system disk only, not the OS disk together with data disks.
Official Reference
About Azure confidential VMs - https://learn.microsoft.com/en-us/azure/confidential-computing
/confidential-vm-overview

You have an Azure subscription that contains a virtual machine named VM1 and a Recovery Services vault named Vault1. VM1 runs Windows Server.
You need to back up VM1 to Vault1 by using Azure Backup. The solution must minimize administrative effort. What should you do first?

• A.From the Vault1 blade in the Azure portal, create a new backup policy.
• B.From VM1, install the Microsoft Azure Recovery Services (MARS) agent
• C.From the Vault1 blade in the Azure portal, select Backup.
• D.From the Vault1 blade in the Azure portal, select Disaster recovery.

The servers run Windows Server and have the network configurations shown in the following table.
Server3 is configured as a NAT gateway. All the servers allow ICMP requests.
Use the drop-down menus to select the answer choice that completes each statement based on the information presented in the graphic.
NOTE: Each correct selection is worth one point.

Exhibit

Exhibit

Exhibit
Exhibit

정답:

Explanation:
Detailed Explanation
Server1 ' s only interface, NIC1 (172.16.0.1/24), sits on the same subnet as Server2 ' s NIC2 (172.16.0.100
/24) - its configured default gateway - so Server1 can reach itself and NIC2 directly, but Server2 has no IP routing/RRAS enabled to forward packets between its two NICs, so traffic aimed at the 192.168.15.0/24 or
131.107.0.0/24 subnets never gets relayed and those pings fail. Server2 can likewise reach its own two directly connected subnets - NIC1/NIC2 on 172.16.0.0/24 and NIC3/NIC4 on 192.168.15.0/24 - but NIC3 has no gateway configured pointing at Server3 ' s NAT interface, so Server2 has no route to the 131.107.0.0
/24 network and cannot reach NIC5. Because Server3 ' s role as a NAT gateway only translates outbound traffic that is actually routed to it, and neither Server1 nor Server2 has the routing/gateway configuration needed to send traffic that far, connectivity in both cases is limited to each server ' s directly attached subnets.
Official Reference
Configure NAT network address translation on Windows Server - https://learn.microsoft.com/en-us
/windows-server/networking/technologies/nat/nat-overview

You have two onpremises Hyper-V hosts named Served and Server2, Server1 contains two virtual machines named VM1 and VM2. Server2 contains three virtual machines named VM21. VM22, and VM23.
You have an Azure subscription.
You plan to use Azure Site Recovery to replicate all the virtual machines to Azure.
You need to deploy the Microsoft Azure Site Recovery Provider to the on-premises infrastructure.
What is the minimum number of providers you should install?

• A.1
• B.2
• C.5
• D.7

You have an Azure virtual machine named VM1. Crash dumps for a process named Process1 are enabled for VM1.
When process1.exe on VM1 crashes, a technician must access the memory dump files on the virtual machine.
The technician must be prevented from accessing the virtual machine.
To what should you provide the technician access?

• A.a managed disk
• B.an Azure Log Analytics workspace
• C.an Azure Blob Storage container
• D.an Azure file share