70-648 무료 덤프문제 온라인 액세스

Your network contains four servers named Server1, Server2, Server3, and Server4 that run Windows
Server 2008 R2. The servers have the Network Policy Server (NPS) role service installed.
You configure a Remote RADIUS Server Group named Group1. Group 1 contains Server2, Server3, and
Server4.
You need to configure load balancing for the members of Group1 to meet the following requirements:
* Server1 must send 25 percent of all authentication requests to Server3.
* Server1 must send 75 percent of all authentication requests to Server2.
* Server1 must only send authentication requests to Server4 if Server2 and Server3 are unavailable.
What should you do from the Network Policy Server console?

• A.* For Server2, set the weight to 75 and the priority to 25. * For Server3, set the weight to 25 and the priority to 75. * For Server4, set the weight to 100 and the priority to 1.
• B.* For Server2, set the weight to 75 and the priority to 75, * For Server3, set the weight to 25 and the priority to 25. * For Server4, set the weight to 100 and the priority to 200.
• C.* For Server2, set the weight to 75 and the priority to 1. * For Server3, set the weight to 25 and the priority to 1. * For Server4, set the weight to 100 and the priority to 100.
• D.* For Server2, set the weight to 1 and the priority to 75. * For Server3, set the weight to 1 and the priority to 25. * For Server4, set the weight to 100 and the priority to 1.

Your network contains a server that runs Windows Server 2008 R2. The server has the Network Policy and Access Services server role installed.
You need to allow only members of a global group named Group1 VPN access to the network.
What should you do?

• A.Add Group1 to the Network Configuration Operators group.
• B.Add Group1 to the RAS and IAS Servers group.
• C.Create a new network policy and define a group-based condition for Group1. Set the access permission of the policy to Access granted. Set the processing order of the policy to 3.
• D.Create a new network policy and define a group-based condition for Group1. Set the access permission of the policy to Access granted. Set the processing order of the policy to 1.

Your network contains a server named Server1 that runs Windows Server 2008 R2. The network for Server1 is configured as shown in the table.

You plan to deploy DirectAccess on Server1.
You need to configure the network interfaces on Server1 to support DirectAccess.
What should you do?

• A.Add the IP address of 10.1.2.2 to LAN1.
• B.Remove the IP of address 131.107.1.13 from Internet2, and then add the address to Internet1.
• C.Add the default gateway of 131.107.1.1 to Internet2.
• D.Remove the IP address of 131.107.1.13 from Internet2, and then add the address to LAN1.

Your network contains a domain-based Distributed File System (DFS) namespace named \\contoso.
com\DFS1.
You have two servers named Server1 and Server2 that are configured as namespace servers for \
\contoso.com\DFS1.
You need to verify that the DFS namespace replicates successfully between Server1 and Server2. Which tool should you use?

• A.dfsrdiag
• B.dfsdiag
• C.dfsutil
• D.dfscmd

Your company is designing its public network. The network will use an IPv4 range of 131.107.40.0/22. The network must be configured as shown in the following exhibit.

You need to configure subnets for each segment.
Which network addresses should you assign?

• A.Segment A: 131.107.40.0/23 Segment B: 131.107.42.0/24 Segment C: 131.107.43.0/25 Segment D: 131.107.43.128/27
• B.Segment A: 131.107.40.0/25 Segment B: 131.107.40.128/26 Segment C: 131.107.43.192/27 Segment D: 131.107.43.224/30
• C.Segment A: 131.107.40.128/23 Segment B: 131.107.43.0/24 Segment C: 131.107.44.0/25 Segment D: 131.107.44.128/27
• D.Segment A: 131.107.40.0/23 Segment B: 131.107.41.0/24 Segment C: 131.107.41.128/25 Segment D: 131.107.43.0/27