642-832 무료 덤프문제 온라인 액세스

The implementations group has been using the test bed to do a `proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?

• A.Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
• B.Under the interface vlan 10 configuration enter standby 10 preempt command.
• C.Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
• D.Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.

The implementations group has been using the test bed to do a `proof-of-concept'. After several changes to the network addressing, routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2(2026::102:1).
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to fault condition?

• A.Under ipv6 router ospf 6 configuration enter no passive-interface default command.
• B.Under ipv6 router ospf 6 configuration enter the network 2026::1:/122 area 0 command.
• C.Under the interface Serial0/0/0.12 configuration enter the ipv6 ospf 6 area 12 command.
• D.Under the interface Serial 0/0/0.23 configuration enter the ipv6 ospf 6 area 0 command.

The implementations group has been using the test bed to do a `proof-of-concept' that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?


Client is unable to ping IP 209.65.200.241

• A.R1
• B.ASW2
• C.R4
• D.R3
• E.ASW1
• F.DSW2
• G.DSW1
• H.R2

You have 2 NTP servers in your network - 10.1.1.1 and 10.1.1.2. You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configure the router?

• A.ntp server 10.1.1.1 ntp server 10.1.1.2 prefer
• B.ntp server 10.1.1.1 ntp server 10.1.1.2 primary
• C.ntp server 10.1.1.1 ntp server 10.1.1.2
• D.ntp server 10.1.1.1 fallback ntp server 10.1.1.2

The following commands are issued on a Cisco Router:
Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router(configuration)#exit
Router#debug ip packet 199
What will the debug output on the console show?

• A.All IP packets passing through the router
• B.All IP packets from 10.1.1.1 to 172.16.1.1
• C.All IP Packets between 10.1.1.1 and 172.16.1.1
• D.Only IP packets with the source address of 10.1.1.1