GB0-381-ENU 문제 151

There are two detailed routes 10.10.1.0/24 1 and 0.10.2.0/24 in the BGP routing table, and the community attributes are 100:1 and 100:2 respectively. Configure aggregate 10.10.0.0 255.255.0.0 in BGP view. What is the community attribute of route 10.10.0.0/16 ?

GB0-381-ENU 문제 152

그림과 같이 PC1과 PC2는 RTC로 ISATAP 터널을 구축합니다. PC2에서 PC1으로 보낸 IPv6 패킷 ______은 RTC에 의해 전달되고 캡슐화된 IPv4 대상 주소는 ______입니다.

GB0-381-ENU 문제 153

In the topology shown in the figure, the following configurations are performed on RTA and RTB respectively:
RTA-ospf-1-area-0.0.0.1]network 192.168.0.0 0.0.0.255
RTA-ospf-1-area-0.0.0.1]network 192.168.1.0 0.0.0.255
RTA-ospf-1-area-0.0.0.1]network 192.168.2.0 0.0.0.255
RTA-ospf-1-area-0.0.0.1]network 192.168.3.0 0.0.0.255
RTA-ospf-1-area-0.0.0.1]network 192.168.4.0 0.0.0.255
RTB] acl number 2000
RTB-acl-basic-2000] rule 0 permit source 192.168.1.0 0.0.0.255
RTB-ospf-1] filter-polic2000 import
Then the possible routes in the RTC routing table are _____

GB0-381-ENU 문제 154

그림에 표시된 토폴로지에서는 RTA, RTB, RTC 및 RTD에서 각각 다음 구성이 수행됩니다.
RTA-LoopBack0] IP 주소 1.1.1.1 255.255.255.255
RTA]ospf 1
RTA-ospf-1]영역 1
RTA-ospf-1-area-0.0.0.1]네트워크 10.0.0.0 0.0.0.255
RTA-ospf-1]가져오기-경로 직접
RTA-ospf-1]default-route-advertise alwa
RTB-LoopBack0] IP 주소 2.2.2.2 255.255.255.255
RTB]ospf 1
RTB-ospf-1]영역 1
rtb-ospf-1-area-0.0.0.1]네트워크 10.0.0.0 0.0.0.255
RTB-ospf-1-area-0.0.0.1]영역 0
rtb-ospf-1-area-0.0.0.0]네트워크 2.2.2.2 0.0.0.0
RTB-ospf-1-area-0.0.0.0]네트워크 20.0.0.0 0.0.0.255
RTC-LoopBack0] IP 주소 3.3.3.3 255.255.255.255
rtc]ospf 1
RTC-ospf-1]영역 0
RTC-ospf-1-area-0.0.0.0]네트워크 20.0.0.0 0.0.0.255
rtc-ospf-1-area-0.0.0.2]네트워크 3.3.3.3 0.0.0.0
rtc-ospf-1-area-0.0.0.0]영역 2
RTC-ospf-1-area-0.0.0.2]nssa no-summarRTC-ospf-1-area-0.0.0.2]네트워크 30.0.0.0 0.0.0.255
RTD-LoopBack0] IP 주소 4.4.4.4 255.255.255.255
측온저항체]ospf 1
RTD-ospf-1]영역 2
RTD-ospf-1-area-0.0.0.2]네트워크 30.0.0.0 0.0.0.255
rtd-ospf-1-area-0.0.0.2]nssa
RTD-ospf-1]가져오기-경로 직접
다음 중 RTD의 라우팅 테이블에 _______이(가) 존재할 수 없는 경로는 무엇입니까?

GB0-381-ENU 문제 155

As shown in the figure, in the IS-IS network, the RTA configuration commands are as follows, please complete them.
RTA]isis
RTA-isis-1]______
RTA-isis-1]interface serial 2/0
RTA-Serial2/0]isis enable 1